The Intel Entry Storage System SS4000-E includes a chassis, Intel XScale Processor based board, with a single Intel XScale 80219 processor, four Serial ATA hard disk drive carriers, one Intel 31244 SATA Controller, dual Intel 82541 Gigabit Ethernet Network controllers, 256MB of DDR SDRAM memory and a single 200 W power supply. Intel-based system boards and chassis have feature sets designed to support the high-density storage market.
The Intel XScale Processor based board that is installed in the Storage System SS4000-E chassis is a printed circuit board with features that were designed to support the storage system market. The architecture is based on the Intel XScale Processor family.
Storage Capacity
Expandable to 1.0 TB – using four 250 GB drives
Expandable to 2.0 TB – using four 500 GB drives NOTE: For specific drive family and capacities supported, please refer to the SS4000-E Tested Hardware and OS List (THOL)
Drive Bays
4 Serial ATA (SATA) Hot Pluggable
Hard Disk Drive Supported
3.5 inch SATA
NOTE: For specific drive family and capacities supported, please refer to the SS4000-E Tested Hardware and OS List (THOL)
Processor
A single Low Voltage Intel® XScale® 80219 processor operating @ 400 MHz
NOTE: The system board is designed to support multiple XScale processors but it is not designed such that the processor can be replaced.
Memory Capacity
1 GB maximum, using 64-bit DDR SDRAM 512 MB maximum, using 32-bit DDR SDRAM
System ships with 256MB memory
NOTE: Only qualified service personnel should service system memory.
Memory Type
Synchronous Dynamic Random Access Memory (SDRAM), PC200 – system ships with 256 MB memory NOTE: For specific memory recommendations please refer to the Tested Hardware and OS List (THOL). Only qualified service personnel should service system memory.
DIMM Slots
One 184-pin DIMM socket
SATA Compliance
SATA 1.5Gb/s
Client Connectivity
Client Connectivity via Dual Gigabit Ethernet
Front Panel
LEDs
Network Ports, Disk Activity / Fault, System Status, Power, Global Disk Activity
Power
Power button
Back Panel
Buttons and Switches
Reset button
I/O Connectors
2x RJ-45 Ethernet ports, 2 USB 2.0 Ports
Power Receptacle
1x IEC AC per installed power supply module
Chassis
Form Factor
Cube chassis
Height
214mm (8.42”)
Width
160mm (6.30”)
Depth
243mm (9.6”)
Weight
As shipped (zero drives): approximately 3.18 kg, 7 pounds
Fully configured (four drives): approximately 5.45 kg, 12 pounds
Shipping container: 9.1 kg, 20 pounds (includes overpack and accessories – with drives)
Height 480mm (18.9”)
Width 385mm (15.15”)
Length 440mm (17.3”)
Color
Black
System Cooling
Fans
Chassis includes one single rotor 92 mm system fan for cooling the hard drives, baseboard and SATA backplane.
The power supply enclosure contains one 40mm fan.
Power
Configuration
200 W continuous power supply. Intel Entry Storage System SS4000-E ships with one 200W power supply
Max AC input current (PS Enclosure)
4 Amperes at 115 Vrms, 2 Amperes at 230 Vrms
Max +3.3 V output
(PS Enclosure)
17.0 A
(total combined power for the+3.3 V and +5 V outputs should not exceed 65 W).
Max +5 V output
(PS Enclosure)
12.0 A
(total combined power for the+3.3 V and +5 V outputs should not exceed 65 W).
Max +12 V output current
(PS Enclosure)
10.0 A
Max -5 V output current (PS Enclosure)
0.3A
Max -12 V output current
(PS Enclosure)
0.5 A
Max +5V Standby output current (PS Enclosure)
1.5 A
Environment
Ambient Temperature
Operating (system): 10 degrees Celsius to +35 degrees Celsius, with maximum change not to exceed 10 degrees Celsius per hour; non-operating (system): -40 degrees Celsius to +70 degrees Celsius.
Relative Humidity
Non-operating: 90%, non-condensing @ 35 degrees Celsius non-condensing
Acoustics
4.7 BA in an idle state in at typical office ambient
Electrostatic Discharge
±15 Kilovolt (KV) per Intel® Environmental test specification
System Cooling Requirement in British Thermal Units (BTU) per Hour
< 680 BTU/hour