Default option is 0, timeout is 2 sec **** 0. Normal mode** 1. No service mode** 2. Maintenance your option:Booting into Normal Mode.Loading kexec....Kernel Image: vmlinuz-2.6.30.2-533064-optCommand Line: console=nsklog ro rootflags=data=ordered md_mod.aamd=0console=ttyS0,115200 raid=part crashkernel=96M@256M panic=1 quietrootdelay=10 idle=poll mk_hdd_rt=md_d10p1 mk_usb_rt=md_d0p1Saving mk log messages into ram ...0 logical volume(s) in volume group "vg1" now activemdadm: stopped /dev/md_d10mdadm: stopped /dev/md_d16Disabling first expansion shelf phys: 0 1 2 3Disabling first expansion shelf phys on right port:[ 58.783710] MD reboot: dropping new IO requests[ 58.788247] MD reboot: waiting for pending IOs to drain[ 61.553148] MD reboot: resuming after draining IOs[ 62.199639] Starting new kernel[ 63.411486] This is a mptsas device. Setting mptsas_availableflag<6>mpt2sas 0000:03:00.0: PCI INT A -> GSI 26 (level, low) -> IRQ 26Starting NimbleOS INITRAMFS boot stageWaiting 10 secs for USB discovery to completeDisabling any watchdog timer set by biosAssembling MD raid devicesbank:0 AA-105345-20140211210657My controller id is 0Reading all physical volumes. This may take a while...Found volume group "vg1" using metadata type lvm2WARNING: This metadata update is NOT backed upWARNING: This metadata update is NOT backed up5 logical volume(s) in volume group "vg1" now activeUsing root device md_d10p1Saving ramfs logs0 logical volume(s) in volume group "vg1" now activeStarting Nimble Array on Supermicromdadm: /dev/md_d0 has been started with 1 drive.Loading module: dca[ 85.042583] dca service started, version 1.8Loading module: hwmonLoading module: usbhidLoading module: ipmi-msghandlerLoading module: ipmi-siLoading module: ipmi-devintfLoading module: loopChecking and mounting system filesystemsMounting file systemsReading all physical volumes. This may take a while.../dev/md_d10: open failed: Device or resource busyFound volume group "vg1" using metadata type lvm2WARNING: This metadata update is NOT backed up5 logical volume(s) in volume group "vg1" now activemount: usbfs already mounted or /proc/bus/usb busymount: according to mtab, /dev/bus/usb is already mounted on /proc/bus/usbfsck not run (successfully) on /scratchLoading module: ixgbe===== System ADate: Wed Apr 16 15:30:49 PDT 2025Restoring mk logs from RAMLoad crashdump kernelLoading module: netlistLoading module: ns_dhmEnabling scsistats collectionModel: CS260Controller SN: NC14A00183MAC Address: 00:25:90:A8:7A:97root: IPMI watchdog params... [DONE]Tuning system runtime parametersBring up interface loBring up interface i2Setting i2 rx-usecs to 7Bring up interface i1Setting i1 rx-usecs to 7Bring up interface eth6Bring up interface eth5Bring up interface eth4Bring up interface eth3Bring up interface eth2Bring up interface eth1Bring up fixed IPNo usable NIC is found for bringing up fixed IPSet up net filtersStarting syslogdChecking update stateChecking system partition quick-rebuild config: [true]md_d0: ro 0 raid10 1 bitmap 1md_d10: ro 0 raid10 0 bitmap 1Setting up memory for system partition quick-rebuildStarting system partition quick-rebuild on md_d10md_d12: ro 0 raid10 0 bitmap 1Starting system partition quick-rebuild on md_d12md_d14: ro 0 raid10 1 bitmap 1md_d16: ro 0 raid10 0 bitmap 1Starting system partition quick-rebuild on md_d16Enabling first expansion shelf phys: 0 1 2 3sleeping for 10 seconds to discover ES expandersroot: Check for required controller specific firmware upgrades...ERROR: Simultanious Multi-threading is Disabled. (It should be Enabled.)ERROR: AES-NI instructions is Disabled. (It should be Enabled.)md5sum: WARNING: 1 of 11 computed checksums did NOT match04/16/2025 22:31:28Starting pmdStarting disk checkNimble Storage ConsoleLANB260-01-A login: